Job Description:

Machinist II - 3rd Shift










Requisition ID:

21071









Job Location(s):

Searcy, AR, US

#job-location.job-location-inline {
display: inline;
}

Job Description

Danfoss Hydraulics Division is currently seeking a Machinist II on 3rdshift to join our team. The position is based at our Searcy, AR facility.Advanced machinist reports directly to the Manufacturing Supervisor as well as designated teams or group leader. You will interact with team/group leader to facilitate the needs of customers and Danfoss by schedule, quality, productivity, and housekeeping. Actively support and strive to meet the strategic goals set by yourself, the facility and Danfoss Corporation.

Job Responsibilities

Responsibilities for this position include, but are not limited to, the following.

• Work from drawings, specifications, programming and setup instructions and data.


• Set up, adjust, check out programming and operate numerically controlled machine tools to perform a series of progressive machining operations on repetitive work to close and exacting tolerances. Finish specifications requiring considerable skill, a general knowledge of machining techniques and methods and familiarity with numerical control machine tool operational procedures.


• Work from programming, operational data and setup instructions defining and coding tool arrangements, fixtures, and material clamping methods. Setup machine calibration and console settings for operations such as bore, mill, drill, face, thread and occasional profiling and contouring.


• Arrange, mount and secure tooling in machine rack. Magazine or turrets, mount, align and secure holding fixture or locate, support and clamp work piece in absence of holding fixtures, set stops, calibrate fixture or work piece to material reference point.


• Install program tape and/or cards in console reader and correlate machine position with control, manually cycle machine through operation sequences to check fixture and work alignment, tooling sequences, clearances, speeds, feeds, etc., and adjust machine to correct deviations from program specifications.


• May be required to operate heat-treating furnaces to change the physical properties of a range of high and low carbon metals to harden, normalize, draw, anneal, etc., by regulating temperatures, controlling heating cycles in accordance with prescribed procedures. Specifications for work which is largely repetitive and where operational methods are standardized.


• May be required to operate laser and/or electron beam welders to meet print requirements for weld geometry using prescribed procedures and specifications for work, which is repetitive and operationally standardized. Must be able to plan and schedule workload.


• May be required to run electro-nickel plating line using prescribed processes from engineering. Must follow process sheets and meet print requirements.


• Employee must follow all safety rules, report all accidents or unsafe conditions to supervision immediately and wear all required personal protective equipment.


• Employee is responsible for the housekeeping of his/her work area and should maintain these areas to the highest degree possible.


• Employee is responsible for the quality of his/her work.


• Attendance and punctuality is a key component in performing his or her job functions

Background & Skills

The ideal candidate possesses these skills.

Required (Basic) Qualifications:

• High School diploma or equivalent


• Minimum requirement is 1 year CNC experience


• Must be able to work in the United States without corporate sponsorship now and within the future


• No relocation benefit is being offered for this position. Only candidates within a 50-mile radius of Searcy will be considered. Active Duty Military Service member candidates are exempt from the geographical area limitation.
  
  

Preferred Qualifications:

• Two years CNC experience We are committed to ensuring equal employment opportunities for all job applicants and employees.

Physical Demands: The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this position. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is occasionally required to stand, walk, sit, use hands to finger dexterity, handle, or feel objects tools or controls, turn/twist, bend at waist, climb stairs, balance, stoop, kneel, crouch or crawl, talk and hear. The employee must occasionally lift and/or move up to 40 lbs. Specific vision abilities required by the job include close vision, distance vision, color vision, peripheral vision, dept perception, and the ability to adjust focus.

Danfoss - Engineering Tomorrow

At Danfoss, we are engineering solutions that allow the world to use resources in smarter ways - driving the sustainable transformation of tomorrow. No transformation has ever been started without a group of passionate, dedicated and empowered people. We believe that innovation and great results are driven by the right mix of people with diverse backgrounds, personalities, skills, and perspectives, reflecting the world in which we do business. To make sure the mix of people works, we strive to create an inclusive work environment where people of all backgrounds are treated equally, respected, and valued for who they are. It is a strong priority within Danfoss to improve the health, working environment and safety of our employees.

Following our founder's mindset 'action speaks louder than words', we set ourselves ambitious targets to protect the environment by embarking on a plan to become CO2 neutral latest by 2030.

Danfoss is an EO employer and VEVRAA Federal Contractor. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, national origin, age, disability, veteran status, or other protected category.

$('span', '.jobdescription').removeAttr("style");

Apply Now