Fabrication Setup & Operate - 2nd Shift at Schneider Electric USA, Inc in Lincoln, Nebraska

Job Description:

What will you do?

This position is responsible for making adjustments on tools, dies, molds, presses, machines, fixtures and equipment to produce parts of the required quality.

• Set up and operate equipment to specified tolerances in the stamping and molding departments and produce quality parts at an adequate rate.


• Inspects parts to blueprints and secures first-piece approval before running.


• Weighs, identifies, and transports parts and materials.


• Notifies supervisor when materials, parts, tools, and equipment are not functioning properly or of the desired quality.


• Checks to be sure safety devices are in place and in proper operation.


• Maintains and lubricates presses, dies, molds, equipment, and related tooling.


• Obtains correct raw stock or parts from designated locations and places them into appropriate material handling equipment.


• Loads stuffers, presses or dies with designated material.


• Places materials, parts, tools, dies, molds, fixtures and equipment in proper locations.


• Makes minor electrical repairs.


• Makes periodic quality checks following inspection procedures.


• Segregates and disposes scrap and offal by type of material.


• Records information on forms for record keeping purposes.


• Keeps equipment and work area clean and orderly.


• May handle plant waste, both hazardous and non-hazardous, in a manner which will insure compliance with local, Nebraska Department of Environmental Quality (NDEQ), and EPA regulations.
  • Hazardous waste handling may include any of the following: dry wastes, contained wastes, moving wastes in-plant, and offering wastes for shipment.
  
  

• GED or High School diploma required.

• Previous work experience preferred, but not required.


• Must be able to pass a skills assessment test on reading and writing comprehension, math skills, and mechanical aptitude.


• Ability to meet production requirements and maintain part quality.


• Ability to use measuring instruments and read blueprints.


• Ability to read, understand and follow procedures to inspect parts.


• Must have the ability to communicate, including verbal and written English.


• Ability to work safely, communicate effectively with supervisors, technical support and peers, use good judgment, and work well around others.


• Ability to cope with stressful situations, following policies and procedures, solve problems and maintain full commitment to the task.


• Ability to utilize good time management skills and multitask without constant supervision


• Ability to use standard tools such as: screw driver, allen wrenches, die grinder, hammers, sockets, end wrenches and other miscellaneous tools.


• Ability to operate forklift, overhead lift, overhead hoist and other material handling equipment and successfully pass standardized certification procedures.


• Frequent forward and lateral reaching.


• Ability to stand for a minimum of 8 hours.


• Occasional moderate force required to push, pull and position molds and dies.


• Frequent grasping and using of tools such as wrenches and die grinder.


• Occasional lifting of objects weighing 22-41 lbs from floor to waist height.


• Occasional forward neck and back flexion.


• Occasional stooping, crouching, squatting, kneeling and balancing.


• Frequent hand-eye coordination of body and work object movements.


• Occasional visual positioning of equipment, adjustments and data entry.


• Occasional visual inspection to check for quality defects, tooling or measuring devices.


• Must have the ability to climb ladder up to 10 feet and work at elevated heights using step ladders and fixed ladders.

What's in it for me?

Schneider Electric offers an inclusive benefits package to support all of our employees such as flexible work arrangements, paid family leave, 401(k) + match, well-being programs, holidays & paid time off, military leave benefits, and more.

Let us learn about you! Apply today.

Why us?

Schneider Electric is leading the digital transformation of energy management and automation. Our technologies enable the world to use energy in a safe, efficient and sustainable manner. We strive to promote a global economy that is both ecologically viable and highly productive.

€25.7bn global revenue

137 000+ employees in 100+ countries

45% of revenue from IoT

5% of revenue devoted for R&D

You must submit an online application to be considered for any position with us. This position will be posted until filled

It is the policy of Schneider Electric to provide equal employment and advancement opportunities in the areas of recruiting, hiring, training, transferring, and promoting all qualified individuals regardless of race, religion, color, gender, disability, national origin, ancestry, age, military status, sexual orientation, marital status, or any other legally protected characteristic or conduct. Concerning agencies: Schneider Electric does not accept unsolicited resumes and will not be responsible for fees related to such.What will you do?

This position is responsible for making adjustments on tools, dies, molds, presses, machines, fixtures and equipment to produce parts of the required quality.

• Set up and operate equipment to specified tolerances in the stamping and molding departments and produce quality parts at an adequate rate.


• Inspects parts to blueprints and secures first-piece approval before running.


• Weighs, identifies, and transports parts and materials.


• Notifies supervisor when materials, parts, tools, and equipment are not functioning properly or of the desired quality.


• Checks to be sure safety devices are in place and in proper operation.


• Maintains and lubricates presses, dies, molds, equipment, and related tooling.


• Obtains correct raw stock or parts from designated locations and places them into appropriate material handling equipment.


• Loads stuffers, presses or dies with designated material.


• Places materials, parts, tools, dies, molds, fixtures and equipment in proper locations.


• Makes minor electrical repairs.


• Makes periodic quality checks following inspection procedures.


• Segregates and disposes scrap and offal by type of material.


• Records information on forms for record keeping purposes.


• Keeps equipment and work area clean and orderly.


• May handle plant waste, both hazardous and non-hazardous, in a manner which will insure compliance with local, Nebraska Department of Environmental Quality (NDEQ), and EPA regulations.
  • Hazardous waste handling may include any of the following: dry wastes, contained wastes, moving wastes in-plant, and offering wastes for shipment.
  
  

• GED or High School diploma required.

• Previous work experience preferred, but not required.


• Must be able to pass a skills assessment test on reading and writing comprehension, math skills, and mechanical aptitude.


• Ability to meet production requirements and maintain part quality.


• Ability to use measuring instruments and read blueprints.


• Ability to read, understand and follow procedures to inspect parts.


• Must have the ability to communicate, including verbal and written English.


• Ability to work safely, communicate effectively with supervisors, technical support and peers, use good judgment, and work well around others.


• Ability to cope with stressful situations, following policies and procedures, solve problems and maintain full commitment to the task.


• Ability to utilize good time management skills and multitask without constant supervision


• Ability to use standard tools such as: screw driver, allen wrenches, die grinder, hammers, sockets, end wrenches and other miscellaneous tools.


• Ability to operate forklift, overhead lift, overhead hoist and other material handling equipment and successfully pass standardized certification procedures.


• Frequent forward and lateral reaching.


• Ability to stand for a minimum of 8 hours.


• Occasional moderate force required to push, pull and position molds and dies.


• Frequent grasping and using of tools such as wrenches and die grinder.


• Occasional lifting of objects weighing 22-41 lbs from floor to waist height.


• Occasional forward neck and back flexion.


• Occasional stooping, crouching, squatting, kneeling and balancing.


• Frequent hand-eye coordination of body and work object movements.


• Occasional visual positioning of equipment, adjustments and data entry.


• Occasional visual inspection to check for quality defects, tooling or measuring devices.


• Must have the ability to climb ladder up to 10 feet and work at elevated heights using step ladders and fixed ladders.